Gorilla Playsets 1500IWF Manual Download Page 158 | Manualshive

Page: 158 / 205

background image

1

HEX BOLT

2

(BETWEEN CHAIN AND

3

4

18TH CHAIN LINK

5/16" WASHER

COUNT OVER 4 LINKS FROM BOLT AND

THE NEXT BOLT GOES IN THIS LINK.

SCALE 1 : 4.5

DETAIL A

BRIDGE DECK BOARD)

5/16" WASHER

5/16" X 1-3/4"

THREE EMPTY LINKS ARE

BETWEEN BOLTS.

A

1: PLACE A 5/16" WASHER BETWEEN THE 18TH CHAIN LINK AND THE BRIDGE DECK BOARD.
2: PLACE A 5/16" X 1-3/4" HEX BOLT WITH 5/16" WASHER THROUGH THE 18TH CHAIN LINK, THEN THROUGH

THE 5/16" WASHER, THEN THROUGH THE HOLE IN THE BRIDGE DECK BOARD AND SCREW IT INTO THE T-NUT.

TIGHTEN THE BOLT BUT NOT SO TIGHT THAT YOU CRACK THE WOOD.
3: COUNT OVER 4 CHAIN LINKS FROM THE LAST HEX BOLT. AT THIS CHAIN LINK PLACE A 5/16" WASHER

BETWEEN THE CHAIN LINK AND THE BRIDGE DECK BOARD. NOTE THAT THREE EMPTY CHAIN LINKS ARE

BETWEEN THE BOLTS.
4: PLACE A 5/16" X 1-3/4" HEX BOLT WITH 5/16" WASHER THROUGH THE CHAIN LINK, THEN THROUGH THE

5/16" WASHER, THEN THROUGH THE HOLE IN THE BRIDGE DECK BOARD AND SCREW IT INTO THE T-NUT.

TIGHTEN THE BOLT BUT NOT SO TIGHT THAT YOU CRACK THE WOOD.
5: REPEAT SUBSTEPS 3 & 4 UNTIL YOU HAVE SECURED THE CHAIN TO THE BRIDGE DECK BOARDS ALONG ONE

SIDE. THEN START OVER WITH THE OTHER CHAIN AND REPEAT THIS ENTIRE PROCESS.

STEP 18: BRIDGE DECK AND CHAIN ASSEMBLY

148

«
...
156
157
158
159
160
...
»

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Related manuals for 1500IWF

Brand: FJC Pages: 2

Brand: Landoll Pages: 70

Brand: H&S Pages: 42

Chicken Coop Plan 3x5

Brand: EASY COOPS Pages: 21

Chicken Coop Plan 4x6

Brand: EASY COOPS Pages: 18

Chicken Coop Plan 8x10

Brand: EASY COOPS Pages: 18

Brand: Vatech Pages: 68

Brand: Yamaha Pages: 16

Brand: Yetter Pages: 24

Brand: Vuly Pages: 4

Brand: PMK Pages: 24

Brand: Meyer Pages: 100

Brand: ASIA TECHNOLOGY Pages: 38

Brand: PR Lighting Pages: 18

Brand: KAPPLER Pages: 36

Brand: Larson Davis Pages: 21

Brand: Spinlock Pages: 28

Brand: Vixen Air Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands