manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 101

ROPE 

LADDER 

SUPPORT

4 X 4 X 29"

CENTER POST

#8 X 3" WOOD SCREW

(2 AT FRONT)

T-NUT

5/16" WASHER

5/16" X 4-1/2"

HEX BOLT

#8 X 3" WOOD SCREW

(3 UNDER DECK)

FRONT FACE BOARD

STEP 42: LOWER LEVEL FRONT CENTER POST

1: LOCATE THE 4 X 4 X 29" CENTER POST.  PLACE THE 4 X 4 X 29" CENTER POST CENTERED 

BEHIND THE HOLE IN THE ROPE LADDER SUPPORT.  CAREFULLY DRILL A 3/8" HOLE 

THROUGH THE CENTER POST USING THE HOLE IN THE ROPE LADDER SUPPORT AS A GUIDE.
2: HAMMER A T-NUT INTO THE HOLE IN THE BACK SIDE OF THE CENTER POST.  FASTEN THE 

CENTER POST TO THE ROPE LADDER SUPPORT WITH A 5/16" X 4-1/2" HEX BOLT AND A 5/16" 

WASHER.
3: SQUARE THE CENTER POST TO THE DECK.  ATTACH THE CENTER POST TO THE FRONT 

FACE BOARD WITH TWO #8 X 3" WOOD SCREWS FROM THE FRONT.  GO UNDER THE FORT 

DECK AND INSTALL THREE #8 X 3" WOOD SCREWS THROUGH THE CENTER DECK BOARD 

INTO THE BOTTOM OF THE CENTER POST.

91

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands