Gorilla Playsets 1500IWF Manual Download Page 181

Page: 181 / 205

ALIGN EDGE OF BORDER UNDER THE DECK

5) It will be very helpful to have an assistant at this stage. We recommend predrilling holes for the screws on the

Have your assistant push down on the board while you install a pan head screw and washer into the hole. Go

bridge deck boards. Mark through the center grommet onto the deck board. Drill a 1/8" hole by 1" deep.

bottom of the deckboards fastened to the chains. Align the edge of the mesh border with the end of the

go from the center grommet to the other side and do the same.

from the center grommet to one end of the mesh and repeat the mark/drill/install fasteners procedure. Then

BOARDS THAT ARE FASTENED TO THE CHAINS.

WITH THE END OF THE 2 X 4 BRIDGE DECK

MARK THROUGH THE CENTER OF THE CENTER

GROMMET ONTO THE MIDDLE DECK BOARD.

DRILL A 1/8" X 1" DEEP HOLE AT THE MARK.

PLACE A PAN HEAD SCREW THROUGH A

WASHER AND INSTALL INTO THE HOLE.

TRY TO CENTER THE WASHER ONTO THE

GROMMET BEFORE TIGHTENING COMPLETELY.

Example picture of the completed

Clatter Bridge Mesh Panels.

Summary of Contents for 1500IWF














































































































































































































Search results

Summary of Contents for 1500IWF

Reviews:

Related manuals for 1500IWF

Brands by name

Popular brands

Gorilla Playsets 1500IWF, Manual

Search results

Summary of Contents for 1500IWF

Reviews:

Related manuals for 1500IWF

Brands by name

Popular brands