manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 70

NOTE:

2 X 4 X 14"

CLARITY.

FROM VIEW FOR 

OF FORT

FRONT

BOARDS REMOVED 

BOTTOM PANEL

#8 X 2" 

WOOD SCREWS

5/4 X 4 X 40-3/8"

DECK SPACER

STEP 11: DECK SPACERS

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD.

1: PRE-DRILL THE ENDS OF THE 5/4 X 4 X 40-3/8" DECK SPACERS TO PREVENT INSTALLATION DAMAGE.  PRE-DRILL 

BOTH ENDS WITH A 1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW.  THE HOLE AT 20-3/16" ONLY NEEDS TO BE 

DRILLED ONCE.  THIS HOLE IS TO ATTACH THE CENTER DECK SUPPORT TO THE DECK SPACER.

2: PLACE THE 5/4 X 4 X 40-3/8" DECK SPACER AT ONE END OF THE FORT.  CENTER THE BOARD BETWEEN THE 

CORNER POSTS AND ATTACH IT WITH 2" WOOD SCREWS THROUGH THE PREDRILLED HOLES INTO THE DECK 

SUPPORT BELOW.  NOTE THE TOP OF THE SCREW HEAD SHOULD BE FLUSH TO THE TOP OF THE DECK SPACER.

3

11

16

3

" 

11

 

" 

 1" 

" 

 20

" 

16

16

8

 2

 1

 

1

8 " 

5/4 X 4 X 40-3/8"

DECK SPACER

60

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands