manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 7

WARRANTY REGISTRATION

Gorilla Playsets

™

 manufactures 

the  finest  quality  products  that 
are  designed  for  outstanding 
strength and durability. We back 
our products with an unparalleled 
warranty.  In  the  unlikely  event 
that  you  will  need  to  contact  us 
about  covered  repairs,  we  must 
have a valid Warranty Registration 
on file.

3 EASY WAYS TO REGISTER

OPTION 1

Fax this completed form to:

(800) 880-3300

OR

Mail this completed form to:

Gorilla Playsets

190 Etowah Industrial Court

Canton, GA 30114

OPTION 2

Complete the online registration form at:

http://www.gorillaplaysets.com/register

OPTION 3

Scan this QR Code with your 

smartphone to complete the 

form using your phone:

Name: _______________________________________________________  Email:  ______________________________________

Address:  __________________________________________________________________________________________________

Comments: ________________________________________________________________________________________________
____________________________________________________________________________________________________________
____________________________________________________________________________________________________________
____________________________________________________________________________________________________________

Would you recommend this product to friends & family?

Please select

your age

How would 

you rate the 

quality of this 

product?

18-30

2-3

41-50

6-7

Yes



  

Excellent



  

Above Average



  

Average



  

Below Average

  

Poor

No

31-40

4-5

51+

8+

How old are 

your children?

Where did you buy this product?

Your registration information:

Date of Purchase 

Store 

Store City 

Store State

Street 

City 

State 

Zip

- CHATEAU II -

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands