manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 93 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 93

 

Administrator Mode

 

4

4.7.5  Multicast 

Note this function is available for 

GV-VS04H 

(Firmware Version 1.03 or later), 

GV-VS11

, 

GV-VS12

 (Firmware Version 1.05 or later) and 

GV-VS14

. 

 
The multicast provides a mechanism for sending a single video and audio stream to a 
group of hosts. Only the hosts that have joined a multicast group can send and receive the 
multicast streams. The multicast streams are only sent to hosts on a local network. 
 
This configuration page provides two settings. One is to allow the GV-Video Server to join 
a multicast group. The other is to allow the GV-Video Server to receive audio broadcasting 
from other hosts in a multicast group. 

 

 

 

    

Figure 4-35 

„

 

Multicast Host Name: 

Name the GV-Video Server in a multicast group.

  

„

 

Multicast Info Update Period: 

Set the time length between each update of multicast 

streams.  

„

 

Multicast Data IP: 

Type the IP address used for multicasting. The default IP address 

is 224.1.1.2.    

                                  

„

 

Multicast Data Port: 

Type the port used for multicasting. The default value is 8300. 

„

 

Multicast Video: 

Select the camera to send its video through multicasting.

  

 

85

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments