manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 117 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 117

 

Advanced Applications

 
 

6

 

Chapter 6  Advanced Applications 

This chapter introduces more advanced applications. 

 

6.1  Upgrading System Firmware 

GeoVision will periodically release the updated firmware on the website. The new firmware 
can be simply loaded into the GV-Video Server by using the Web interface or the

 GV-IP 

Device Utility

 included on the Software CD/DVD. 

 

Important Notes before You Start  

Before you start updating the firmware, please read these important notes:  

1.  While the firmware is being updated, make sure the following: 

A.  The power supply must not be interrupted. 
B.  The Ethernet cable must not be unplugged if the cable is the source of power 

supply (Power over Ethernet or PoE supported). 

2.  Do not turn the power off in 10 minutes after the firmware is updated. 

 

WARNING:

 The interruption of power supply during updating causes not only update 

failures but also damages to your GV-Video Server. In this case, please contact your 
sales representative and send your device back to GeoVision for repair. 

IMPORTANT:

 After upgrading the firmware of GV-Video Server to the latest version, it 

is required to 

format the storage device

 for better recording efficiency and stability. To 

format the storage device, be sure to back up the data first and see 

4.8.3 Storage 

Settings

 for how to format the storage device.

 

 

 

109

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments