manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 13 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 13

 

Introduction

 
 

1 

1.6  Options  

Optional devices can expand your GV-Video Server’s capabilities and versatility. Contact 
your dealer for more information. 

 

GV-GPS Receiver 

The GV-GPS Receiver is a Global Position System 
receiver. With the GV-GPS Receiver, you can perform GPS 
tracking and location verification of the GV-Video Server. 
Two types of interfaces are available: UART (for GV-
VS04H/GV-VS14) and RS-232 (for GV-VS12).  

GV-Relay V2 

Working with the GV-Relay V2, the GV-Video Server is 
capable of driving the loads of relay outputs over 5 volts. 

GV-Storage System 

The iSCSI storage system allows you to record files over 
the Internet. 

GV-WiFi USB Adaptor 

The WiFi USB Adaptor is designed to connect the GV IP 
devices, such as GV-Video Server or GV-Compact DVR, to 
the wireless network. 

GV-PA191 PoE 
Adaptor 

The GV-PA191 is designed to provide power to the IP 
device through a single Ethernet cable. The GV-PA191 is 
only supported by GV-VS04H and GV-VS12. 

GV-VR605A DC 
Voltage Regulator 

With the GV-VR605A, you can install GV-Video Server in 
the car. The GV-VR605A will supply and maintain a 12V 
voltage to the GV-Video Server and its connected cameras.

Access Control Series 
The GV-Video Server can work with the Wiegand-interface card reader to send 
cardholder data to the central monitoring stations Center V2 and VSM, as well as GV-
System. The following devices are only supported by GV-VS04H and GV-VS14.

 

GV-Reader  

GV-Reader includes transmit-receive antenna and 
electronics. Featured with the Wiegand output, the unit is 
compatible with any standard access control panel. 

GV-R1352 Card 
Reader 

The GV-R1352 is a card reader designed to recognize 
identification cards. Featured with the Wiegand output, the 
unit can be connected to any standard access control 
panel. The GV-R1352 comes with a weather sealed and 
IP66 compliant housing for outdoor use. 

 

5

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments