GeoVision GV-VS11 User Manual Download Page 176

Page: 176 / 185

10.6.2 Accessing Live View

You can tap the information button at the top-right corner to see the connection
information.

Figure 10-35

The buttons below are available when the iPhone, iPod Touch or iPad is positioned vertically.

Icon

Name

Function

Screen

division

Displays up to four channels on the same page if the GV-
IP device supports multiple channels.

PTZ control

Enables PTZ control. Drag across the camera live view
screen to adjust the camera position. The following
buttons are available:

•

: Zooms in and out.

•

: Adjusts the focus.

•

: Moves the camera back to Home position.

•

: Adjusts the iris. (GV-SD010 only)

•

: Moves the camera to a preset point by typing the

preset number.

Snapshot

Saves the current image in the mobile device.

I/O Device

Tap a number to force the output device to be triggered.
The I/O icon

will be highlighted briefly when I/O is

triggered.

Stream
change

Switch the live view streams.

168

Summary of Contents for GV-VS11


























































































































































































Search results

Summary of Contents for GV-VS11

Reviews:

GeoVision GV-VS11, User Manual, Page: 176 / 185

Search results

Summary of Contents for GV-VS11

Reviews: