manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 12 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 12

 

1.3  System Requirement 

To access the Web interface of the GV-Video Server, it is required to use Microsoft 
Internet Explorer 7.x or later. 

 

Note:  

1.  For the users of 

Internet Explorer 8 or later

, additional settings are required. For 

details, see

 Appendix A

. 

2. 

Internet Explorer 10

 is not supported in all the firmware of GV-Video Server. 

 
 

1.4  PoE Support  

The models supporting PoE (Power over Ethernet) include: 

•

 

GV-VS04H and GV-VS12  

 

When the PoE (Power over Ethernet) function is used, please note: 

•

 

The I/O terminal functions cannot work. Don’t connect any devices to the I/O terminal 
block on the rear panel of the unit. 

•

 

External power supply is required for USB storage device when used for recording. 

 
See “Power over Ethernet” in 

Specifications

 later in this manual before purchasing a PoE 

adaptor.  

 

1.5  GPS Support 

Attached with the GV-GPS Receiver, the GV-Video Server allows you to perform vehicle 
tracking on Google Maps. The models supporting GPS function include: 

•

 

GV-VS04H, GV-VS12 and GV-VS14. 

 
Different models of the GV-Video Server support different interfaces:  

•

 

UART:

 GV-VS04H and GV-VS14 

•

 

RS-232:

 GV-VS12  

 

 

4 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments