manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 106 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 106

 

[Host Settings]

 Enter a descriptive name for the GV-Video Server.  

 

[Auto Reboot Setup] 

Select 

Enable

 to activate automatic reboot and specify the time for 

reboot in the sub fields. 

„

 

Day Interval: 

Type the day interval between each reboot. 

„

 

Reboot Time:

 Use the drop-down lists to specify the time for automatic reboot. 

Note this function is available for 

GV-VS04H 

(Firmware Version 1.03 or later), 

GV-VS11

,  

GV-VS12

 (Firmware V1.04 or later) and 

GV-VS14

. 

 

[Repair Record Database] 

Click 

Apply 

to repair the database when errors occur while 

playing back the recordings with the Remote ViewLog player.  Problems can occur when 
there are errors in firmware or damages to the storage device. 

Note this function is available for 

GV-VS04H

 (Firmware Version 1.03 or later), 

GV-VS11

, 

GV-VS12

 (Firmware Version 1.04 or later), and 

GV-VS14

. 

 

[Repair Database Status]

 This field displays the repairing status of database. 

  

 

[Firmware Update] 

This field displays the firmware version of the GV-Video Server. 

 

[System Settings] 

Clicking the 

Load Default

 button will make the GV-Video Server 

restore factory default settings. The Ready LED on the front panel will turn off. Wait until 
the Ready LED turns on and re-log in the server. After applying the default settings, you 
will need to configure the GV-Video Server’s network setting again. 

 

[Internal Temperature]

 This field displays the current chipset temperature inside the GV-

Video Server. Note this function is only available for 

GV-VS14

.  

 

[Reboot] 

Clicking the 

Reboot 

button will make the GV-Video Server perform the software reset. The 

Ready LED on the front panel will turn off. Wait until the Ready LED turns on and re-log in 
the server.  

 

 

 

98 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments