manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 40 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 40

 

Comparison Table for Major Functions 

The options or functions on the left menu of the Web interface (Figure 4-1) may vary 
depended on models. The table below provides the information of major differences in 
supported functions. 
 

                Model 
 
Function 

GV-VS04H 

(Firmware 
V1.03 or later)

 

GV-VS11 

(Firmware V1.0 
or later)

 

GV-VS12 

(Firmware 
V1.02 or later)

 

GV-VS14 

(Firmware V1.0 
or later)

 

Dual Streams 

No Yes No Yes 

Wiegand 

Yes 

No 

No Yes 

Buzzer 

Yes 

No 

No 

No 

Multicast 

Yes Yes 

 Yes Yes 

Tampering Alarm 

Yes Yes 

 Yes Yes 

Watermark  

Yes Yes 

 Yes Yes 

Text Overlay 

Yes Yes 

 Yes Yes 

Video Channel 
Source Settings 

Yes 

No  

No 

No 

System Log 

Yes Yes 

 Yes Yes 

GV-Backup Center 
Connection 

Yes Yes 

 Yes Yes 

GV-Video Gateway 
Connection 

Yes Yes 

 Yes Yes 

GV-GIS Connection

Yes 

No  

Yes 

Yes 

 

 

32 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments