manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 124 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 124

 

6.4  Restoring to Factory Default Settings 

Among different models of GV-Video Server, the operation of restoring the GV-Video 
Server to original default values can vary and the way the LEDs flash can also be different. 

 

To restore to default settings, use the 

Reset 

and 

Load Default 

buttons on the front panel. 

For the location of the two buttons see 

1.7 Physical Description

. 

 

Restoring GV-VS04H and GV-VS14 to Default Settings 

1.  Press and then release the 

Reset

 button immediately. 

2.  Press and hold the 

Load Default

 button until all 3 LEDs (Power, Ready and Disk 

Full/Fault) are on. This may take up to 30 seconds. 

3. Release the 

Load Default

 button. The process of loading default values is complete, 

and the GV-Video Server starts rebooting itself with all 3 LEDs turning off.  

4.  Wait until the Power and Ready LEDs turn on again. After this all the settings are 

returned to default values.  

 

Restoring GV-VS11 and GV-VS12 to Default Settings 

1.  Unplug and plug the power cable to start.  

2.  Press and hold the 

Default

 button until the Ready LED blinks. This may take up to 30 

seconds. The Ready LED will blink twice.  

3. Release the 

Default 

button. The process of loading default values is complete, and the 

GV-Video Server starts rebooting itself with the 2 LEDs turning off.  

4.  Wait until the Power and Ready LEDs turn on again. After this all the settings are 

returned to default values.  

 

Note: 

Before the 

Ready LED

 is on again, do not unplug the power cable; otherwise the 

loading of default values will fail. 

 

 

  

 

116 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments