manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 182 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 182

 

C.  Supported Mobile Broadband Device 

GV-VS04H / GV-VS12 / GV-VS14 

Vendor  

Model 

Bandluxe C320, 

C501 

Huawei 

E156, E156B, E169, E220, E303, E353,  E1692, E1750, E1752, E1756, 
E1756C, EC169C, EC189 USB Modem 
(HSDPA/UMTS/EDGE/GPRS/GSM) 

Novatel 

MC950D, MC996D, MC998D (HSDPA/UMTS/EDGE/GPRS/GSM) 

Onda MSA523HS 

Sierra 250U 

Verizon 

USB727, USB728, USB760 Modem (EVDO) 

Vodafone 

K3565 (Rev 2) 

ZTE MF100 

Note:

 Huawei E1756C is only supported by GV-VS12 and GV-VS14. 

 

GV-VS11 

Vendor  

Model 

Huawei 

E169, E220, EC169C, E1750, E1756, E1756C, EC189 USB Modem 
(HSDPA/UMTS/EDGE/GPRS/GSM) 

Novatel MC998D 

(HSDPA/UMTS/EDGE/GPRS/GSM) 

 

D.  The RTSP Command 

The GV-Video Server can support RTSP protocol for both audio and video streaming.  

 

If you use the QuickTime player, enter: 
rtsp://<IP of the GV-Video Server:8554/<CH No.>.sdp 
For example, rtsp://

192.168.3.111

:8554

/CH001

.sdp  

 
If you use the VLC, enter: 
rtsp://username:password@<IP of the GV-Video Server:8554/<CH No.>.sdp 
For example, rtsp://

admin:admin

@

192.168.3.111

:8554/

CH001

.sdp  

 

Note: 

1.  The RTSP server must be enabled on the Web interface. See 

4.3.9 3GPP / RTSP

. 

2.  Only VLC and QuickTime players are supported for video streaming via RTSP protocol.
3.  For GV-VS11 and GV-VS12, only 352 x 240 (352 x 288) and 176 x 112 (176 x 144) are 

supported. 

 

174 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments