manualshive.com logo in svg

GeoVision GV-VS11, User Manual, Page: 128 / 185

Share
Download
GeoVision GV-VS11 User Manual Download Page 128

 

•

 

The maximum number of streams that a GV-Video Server allows is 8 (GV-VS04H) /  

16 (GV-VS14) / 4 (GV-VS11 and GV-VS12). For 

GV-VS04H 

and 

GV-VS12

, when a 

channel is connected to GV-System, IE browser, or any other application, it takes up 1 
stream. For 

GV-VS11 

and

 GV-VS14 

with dual-stream function, when a channel is 

connected to IE browser or any other application, it takes up 1 stream; when a channel 
is connected to GV-System, it takes up 2 streams. 

 

Note: 

When you connect over the maximum number of streams specified above, a warning 

message “Too many users” will pop up, and no image can be accessed after the threshold.

 

•

 

The codec and recording resolution of digital videos are set up on the GV-Video Server 
instead of on the GV-System. 

•

 

The hardware compression and the “Pre-Recording Using RAM” feature cannot work 
on the videos from GV-Video Server. For details about the “Pre-Recording Using RAM” 
feature, see “System Configuration”, Chapter 1, 

User’s Manual

 on the Surveillance 

System Software CD/DVD.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

120 

Summary of Contents for GV-VS11


























































































































































































Reviews:

No comments