manualshive.com logo in svg

GeoVision GV-Video Server, User Manual

Share
Download
GeoVision GV-Video Server User Manual Download Page 79

 

Administrator Mode

 

 

71

4

[Start monitoring by Input X]  

Start monitoring by the assigned input. When the assigned 

input is triggered, the system will respond based on your recording or input monitoring 
settings in above 

Manual

 or 

Schedule

 options. 

 

[Stop monitoring by Input X] 

Stop monitoring by the assigned input. When the assigned 

input is triggered, the system will stop monitoring. 

„

 

Remove HDD:

 When the monitoring is stopped by the input trigger, the storage device 

will also be removed from the system.  

„

 

ACC Signal:

 The option is designed for the use of GV-VR605A DC Voltage Regulator. 

With the GV-VR605A, the GV-Video Server can be installed in the car. When the car 
ignition is turned off, the GV-Video Server will remove the storage device from the 
system and turn off automatically. For details, see 

GV-VR605A Installation Guide

. 

 

Note:

 The ACC Signal option is not functional in version 1.05.

 

 

[Camera Status Icon] 

: 

Manual recording                     

: 

Schedule recording 

 

: 

On standby

                             

: 

Enabled for motion detection and input trigger 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for GV-Video Server




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands