GeoVision GV-Video Server User Manual Download Page 145

Page: 145 / 179

Mobile Phone Connection

137

Supported Resolution and Codec

Handheld
Device View

GV-GView
V2

GV-MSView
V2/ V3

GV-SSView
V3

3GPP
Viewer

GV-AView V1

Eye V1 / HD
V1

MPEG4

320 x 240 or below

320 x 240

or below

704 x 480 or below

MJPEG

X X

704 x 480 or

below

H.264

X X

320 x 240 or

below

1280 x 960 or

below

Note:

A “X” mark indicates the mobile phone application does not support the codec. The live

view will not be displayed on the mobile phone if you select the unsupported codec.

Note:

1. For the 3G-enabled mobile phone, you can receive live video from the GV-Video Server

without installing any GV mobile applications.

2. To receive the live video from the GV-Video Server, enter the TCP/IP port on your mobile

phone. To play video back, enable ViewLog Server on the GV-Video Server and enter the
RPB Port on your mobile phone.

Summary of Contents for GV-Video Server




















































































































































































Search results

Summary of Contents for GV-Video Server

Reviews:

Brands by name

Popular brands

GeoVision GV-Video Server, User Manual

Search results

Summary of Contents for GV-Video Server

Reviews:

Brands by name

Popular brands