manualshive.com logo in svg

GeoVision GV-Video Server, User Manual

Share
Download
GeoVision GV-Video Server User Manual Download Page 106

 

 

98 

Chapter 5  Recording and Playback 

The GV-Video Server can record down video/audio directly to the attached USB mass 
storage device. And you can play back the recorded files on the GV-System or over the 
TCP/IP network. 

 

5.1  Recording 

To enable the recording function: 

 

1.  Attach the USB mass storage device to the GV-Video Server. See

 

4.8.3 Storage 

Settings

. 

2.  If you like to set up the pre-recording, post-recording or audio recording, see

 4.1.2 

Video Settings

. 

3.  If you like to set up the schedule for video recording or I/O monitoring, see

 4.5 

Recording Schedule

. 

4.  If you like to configure the areas and sensitivity values for motion detection, see

 4.1.3 

Motion Detection

. 

5.  If you want the recording to be triggered by input device, configure the operation of I/O 

devices. See 

4.2.2 Input/Output Settings

. 

6.  To start recording and I/O monitoring, see 

4.4 Monitoring

. 

The GV-Video Server will start recording in case of motion detection, I/O trigger, or during 
the scheduled time. 

 

5.2  Playback 

Two methods are available to play back the video files recorded at the GV-Video Server: 

•

 

Playback using the USB mass storage device by attaching it directly to the GV-
System 

•

 

Playback using the Remote ViewLog function over the TCP/IP network 

 

Summary of Contents for GV-Video Server




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands