manualshive.com logo in svg

GeoVision GV-Video Server, User Manual

Share
Download
GeoVision GV-Video Server User Manual Download Page 72

 

 

64 

4.3.6  Backup Center 

Note the function is only available for 

GV-VS04A

, 

GV-VS04H 

(Firmware Version 1.03 or 

later), 

GV-VS11

 and 

GV-VS12 

(Firmware Version 1.02 or later). 

 
The connection to GV-Backup Center allows you to back up another copy of recordings 
and system log to a PC-based GV-Backup Center while the GV-Video Server is saving 
these data to the attached storage device. If a disaster strikes where the GV-Video Server 
is located, the recording data remain safe in a different location.  

 

 

                                                

Figure 4-24 

To enable the GV-Backup Center connection: 

1. 

Activate Link: 

Enable the connection to GV-Backup Center.

 

2. 

Host Name or IP Address: 

Type the host name or IP address of GV-Backup Center.

 

Summary of Contents for GV-Video Server




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands