manualshive.com logo in svg

GeoVision GV-Video Server, User Manual

Share
Download
GeoVision GV-Video Server User Manual Download Page 14

 

 

6 

1.7  Physical Description  

 

This section identifies the various components of the GV-Video Server. 

1.7.1  Front View 

1.7.1.1  GV-VS04A 

 

Figure 1-5 

No.  Name  

Function  

1  Video Input   

4 plugs for video inputs.  

2  Speaker Output  

A plug for the speaker device. 

3  Audio Input  

Each plug is for 2 audio inputs.  

4 Reset 

 

It reboots the GV-Video Server, and keeps all current 
configurations.   

5  Default Button  

It resets all configurations to their factory settings. See

 6.4 

Restoring to Factory Default Settings

.  

6 

Disk Full/Fault 
LED  

This LED is on, indicating the hard drive is full or faulty. 

7 Ready 

LED 

 

This LED is on, indicating the GV-Video Server is ready for 
connection. 

8  Power LED 

This LED is on, indicating the power is supplied. 

 

Summary of Contents for GV-Video Server




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands