GeoVision GV-Video Server User Manual Download Page 25

Page: 25 / 179

Accessing the GV-Video Server

3.2 Functions Featured on the Main Page

This section introduces the features of the

Live View

window and

Network Status

on the

main page. The two features are accessible by both Administrator and Guest.

Main Page of Guest Mode

▼

Video and Motion

▼

Live View

►

Camera 1

►

Camera 2

►

Camera 3

►

Camera 4

►

4 Cameras

▼

Network

►

Status

Figure 3-2

Main page of GV-VS04H in Guest Mode

For

GV-VS11

users, you can process one video stream in two different codec and image

settings. In the Administrator mode, both streams are available. Click

Streaming 1

Streaming 2

in the left menu to access the live view. In the Guest mode, only one stream is

available.

Summary of Contents for GV-Video Server




















































































































































































Search results

Summary of Contents for GV-Video Server

Reviews:

Brands by name

Popular brands

GeoVision GV-Video Server, User Manual

Search results

Summary of Contents for GV-Video Server

Reviews:

Brands by name

Popular brands