background image

 

V 10/17 

38  

  Troubleshooting 

MagicCompact BA04 

Problem/error/malfunction 

Procedures/remedy 

The pressure increase is indicat-
ed on the filter pressure gauge 

 

Pressure increase on the filter 
cartridges 

Switch off the gun control units, 
wait until the differential pressure 
returns to normal again. Check 
the cleaning cycles by ear, if 
necessary, shorten the pause 
times in the cleaning cycle. 
Check, if the cleaning pressure is 
set on 5 bar on the pressure in-
put valve (see also the section 
"Troubleshooting" in the After Fil-
ter operating manual) 

ATTENTION: 
If the pressure gauge shows a 
pressure rise higher than 3 
kPa, contact your Gema agent 
immediately!

 

Alarm has been released: 
Message

 Fan overpressure

 

 

Minimum pressure in filter hous-
ing not reached – corresponding 
pressure gauge responding 

Too little pressure, too much ex-
haust air, because too little or no 
air resistance 
Filter housing door is open 
Sieve machine not fitted tightly 
on the cyclone separator 
Waste container not fitted tightly 
(see also the troubleshooting 
section in the After Filter manual) 

Alarm has been released: 
Message 

Fan low pressure

 

 

Maximum pressure in the filter 
housing exceeded – correspond-
ing pressure gauge responding 

Pressure too high, insufficient 
exhaust air because the air re-
sistance is too high 
Filter clogged (valves defect or 
cleaning pressure too low, at 
least 5 bar) 
Poor compressed air quality 
(contains oil or water) 
Malfunctions on running-in, until 
the filter cake is built up on the 
filter cartridges (see also the 
"Troubleshooting" section in the 
After Filter operating manual) 

Alarm has been released: 
Message

 Guns not OK 

 

Diagnostic adaptor of the guns 
indicates, that no high voltage is 
being produced 

Turn on the gun control unit, or 
correct the fault in the gun control 
unit or gun with the information in 
the corresponding operating in-
structions 

Summary of Contents for MagicCompact BA04






















































Reviews: