Geely MK Series Owner'S Manual Download | Manualshive

Page: 71 / 188

background image

Notes on MP3

Please don't connect portable hard disk

or other flash card and MP3 player to the

interface as music sources whereas the

especial circumstances in a car. We will not

with responsibility for the maintenance when

they are mangled, and will not make any

compensations.

Notes on CDs

Use only CDs with the following mark.

The unit can play CD-R and CD-RW, the play
ability may be slightly different from CDs.
A dirty or defective disc may cause sound
dropouts while playing.
Hold the disc by its edge when operation.

Do not touch the side without mark.
Do not stick paper or tape and other things on
the surface of the disk.

Do not expose the discs to direct sunlight or
heat sources.
Clean the discs with a soft cloth, wipe each
disc from centre out.

Do not use solvent such as benzene or alcohol
to clean the discs.
The unit can not play 3 inch (8cm) discs.
Do not use erose discs such as heart-shaped
and octagonal, Which may cause trouble.

Do not expose the discs to direct sunlight or
heat sources.

25. Audio System

64

Part I

«
...
69
70
71
72
73
...
»

Summary of Contents for MK Series





























































































































































































Reviews:

No comments

Related manuals for MK Series

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

RadioPRO 5 RP5-GM41

Brand: PAC Pages: 3

Brand: iDataLink Pages: 99

Brand: TBC Pages: 12

Brand: kincrome Pages: 6

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: Ecco Pages: 9

Brand: SNIPER Pages: 2

Brand: Cadillac Pages: 335

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands