Geely MK Series Owner'S Manual Download

Page: 78 / 188

Sound Adjustment

1.Press to power on.

2.Press the SEL/LOUD button to select the

item which you wish to adjust:

BAS(bass), TRE(treble), BAL(balance),

FAD(front&back) and VOL(volume).

Corresponding to the above items, the

following display occurs in cycle and

repeatedly.

EQ Control

Press the EQ/MUT button to switch BT/FLAT/

JAZ/POP/CLAS/ROCK/VOCAL equalizer effect.

MUTE Control

Press the MUT button to switch to the mute

mode, the "MUTE" flash on the LCD. Press

again to cancel.

The function of mute control is only for receiver.

LOUD Control

Press the SEL/LOUD button to increase the

bass volume and treble volume (especially

when it is tiny sound),the "LOUD" will display

on the LCD.Press again to cancel.

3.Press the VOL+ and VOL- button to adjust

the sound.

Adjust each item according to the display on

the display screen.

When not pressing the MOD/LOU button, the

VOL- and VOL+ are the volume adjusting

button.

Part I

Summary of Contents for MK Series





























































































































































































Search results

Summary of Contents for MK Series

Reviews:

Related manuals for MK Series

Brands by name

Popular brands

Geely MK Series, Owner'S Manual

Search results

Summary of Contents for MK Series

Reviews:

Related manuals for MK Series

Brands by name

Popular brands