Geely MK Series Owner'S Manual Download Page 130

Page: 130 / 188

3. Connect the cable in the order of a, b, c,

and d.

a: connect the clip of positive (red) jump

cable to the positive connector (+) of the
discharged battery.

b: connect clip at the other end of positive

(red) jump cable to the positive connector
(+) of the charging battery.

c: connect the clip of negative (black)

jump cable to the negative connector (-) of
the charging battery.

d: connect clip at the other end of negative

(black) jump cable to a unpainted metal
point on the vehicle with the discharged
battery.

The connecting point is shown in the following

figure:

Positive connector
( mark "+" )

Charging

battery

Positive con

nector

( mark “+”)

Jump cable

Discharged

battery

Charging battery

Negative connector
( mark “-” )

123

Part III

Summary of Contents for MK Series





























































































































































































Search results

Summary of Contents for MK Series

Reviews:

Brands by name

Popular brands

Geely MK Series, Owner'S Manual

Search results

Summary of Contents for MK Series

Reviews:

Brands by name

Popular brands