manualshive.com logo in svg

Geely MK Series, Owner'S Manual

Share
Download
Geely MK Series Owner'S Manual Download Page 93

Trouble shooting

Press the “RESET” button to resume original 

estate when operations are invalid, but your 

manual settings will be loosed.

                CAUSE   

 

 

 

 

The power connection is 

not correct. 

The volume control was 

lower. 

The  vehicle  ignition  is 

switched off. The fuse is 

blown.

The antenna cable is not 

connected. 

The signals are weak

The signals are weak

RESET

Maintenance

Clean front panel

When the front panel gets contaminated, you 

can wipe the surface with a soft dry cloth.

Design and specifications are subject to change 

without notice.

            SYMPTOM   

 

 

 

No sound after power on  

No power  

 

No radio reception   

The radio does not stop on 

any stations when tuning.

            SOLUTION   

Adjust the volume Check 

h e   2 4 V   a n d   g r o u n d 

connections.

Switch the ignition to the  

“ON” or  “ACC” position 

replace  the  fuse  with  a 

same one.

Insert the antenna cable 

firmly  into  the  antenna 

jack on the unit.

Select  a  station  with 

manual tuning.

  86

Part I

Summary of Contents for MK Series





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands