manualshive.com logo in svg

Geely MK Series, Owner'S Manual

Share
Download
Geely MK Series Owner'S Manual Download Page 4

Important Information in This Manual 

Safety and Vehicle Damage Warning                              

There are safety warning and vehicle damage warning in this man-
ual, you have to avoid the possible body injury or vehicle damage 
by following the instructions in these warnings. 
The types of warnings in this manual are described as below:

Safety Mark

Notice

For warning: negligence of the warning will result in vehicle or 
equipment damage. The driver shall be prompted what to do or 
not to do in order to avoid or reduce the chance of damage to the 
vehicle or equipments.

When the above safety mark is seen, it indi-
cates “no”, “do not” or “never let it happen”.

Warning

For warning: negligence of the warning will result in human 
body injury. The driver shall be prompted what to do or not to 
do in order to lower the risk of injury to himself and others.

Summary of Contents for MK Series





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands