GE ZIC30GN Technical Service Manual Download Page 56

Page: 56 / 83

– 56 –

Filter Head

To remove the

ﬁ

lter head:

1. Remove the water valve. (See

Water Valve

, follow

steps 1 thru 6.)

2. Remove the Phillips-head screw that attaches

the

ﬁ

lter head bracket to the right-side frame.

3. Pull

the

ﬁ

lter head forward.

4. Remove the 4 Phillips-head screws (2 on each

side) that attach the

ﬁ

lter head cover.

5. Remove the 2 Phillips-head screws from the

ﬁ

lter

head.

Bracket

Filter Head

EMI Filter

The EMI

ﬁ

lter is located on the left side of the

machine compartment. The EMI

ﬁ

lter is attached

to the

ﬁ

lter bracket with a Phillips-head screw. The

toeplate and vent panel must be removed to access
the inverters. (See

Toekick and Vent Panel

Note:

When installing the EMI

ﬁ

lter, ensure all

ﬁ

lter

wiring is connected to the correct terminals.

Check the EMI

ﬁ

lter for approximate resistance value

at the following locations:

White (neutral input) to white (neutral output) - 0



Black (line input) to black (line output) - 0



White (neutral input) to black (line input) - 470K



Input-L

Input-N

Output Wire Harness

Filter Bracket

https://appliancetechmanuals.com

Summary of Contents for ZIC30GN




















































































Search results

Summary of Contents for ZIC30GN

Reviews:

Related manuals for ZIC30GN

Brands by name

Popular brands

GE ZIC30GN, Technical Service Manual

Search results

Summary of Contents for ZIC30GN

Reviews:

Related manuals for ZIC30GN

Brands by name

Popular brands