GE 86498 ETHER-1000 UNIT Technical Practice Download Page 23 | Manualshive

Page: 23 / 174

GE 86498 ETHER-1000 UNIT Technical Practice Download Page 23

342-86400-498PS

Issue 1.2

April 2012

Page 23

Copyright



GE Multilin Inc. 2010-2012

Path Protection

The  TDM  pipes  connected  in  ring  topologies  offer  the  capability  for  traffic/route
diversity.    Normally,  unicast  traffic  is  routed  to  the  destination  port  through  the
path  with  the  fewer  ETHER-1000/ETHER-100  hops  and  the  broadcast/multicast
traffic  is  routed  half  way  around  the  ring  simultaneously  in  both  clockwise  and
counte

rclockwise directions in a “drop-and-continue” manner. If a failure occurs

in a JMUX unit, or a fiber is damaged, affected traffic will be automatically
rerouted to the other way around the ring typically within 5 ms.

Note:

Path protection is carried out independently for each TDM pipe configured

and provisioned as a ring.

Physical  ETHER-1000  unit  redundancy  can  be  achieved  by  equipping  an
ETHER-1000  drop  site  with  two  ETHER-1000  units  installed  on  separate
paddleboards.    These  units  can either  be installed on separate  CBW ports  (this
would assume establishing completely independent ETHER-1000 systems using
separate  STS-1  channels),  or  on  the  same  CBW  ports  (using  two  cascaded
ETHER-1000  units).    At  each  ETHER-1000  drop  site,  an  Ethernet  station/LAN
would  then  be  connected  to  both  unit  paddleboards  through  an  external  switch
with  a  protection-switching  feature  (e.g.  Rapid  Spanning  Tree)  enabled.    An
example  of  a  fully  redundant  ETHER-1000  application  at  an  OC-48  JungleMUX
node is shown in Figure 10.

CAUTION

When “redundant” ETHER-1000 units are simultaneously bridging the same

traffic, an Ethernet loop is created which can cripple the network if not

properly handled. Traffic must, therefore, be connected through an

external switch with a feature such as Spanning Tree or Rapid Spanning

Tree enabled.

«
...
21
22
23
24
25
...
»

Summary of Contents for 86498 ETHER-1000 UNIT















































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands