GE 86498 ETHER-1000 UNIT Technical Practice Download | Manualshive

Page: 121 / 174

background image

342-86400-498PS

Issue 1.2

April 2012

Page 121

Copyright



GE Multilin Inc. 2010-2012

Port

Allows the user to select the port for which the information will be displayed.
Note that the labels for those paddleboard ports that are available but presently
disabled are grayed out although their statistics can be viewed.

Errored Frame Counts

Long Frames

Increments on reception of a frame longer than 1632 bytes, and less
than 2033 bytes (longer frames are counted as “jabber”). These
frames are discarded.

Short Frames

Increments on reception of a frame shorter than 64 bytes with valid
FCS (CRC) check. (Compare with

Fragments

counter definition

below.)

CRC Errors

Increments on detection of Frame Check Sequence (CRC) errors.
FCS  is  carried  in  the  last  4  bytes  of  the  frame.    FCS  is  used  for  a
"validity"  check  on  each  Ethernet  frame.    If  the  frame  has  been
corrupted  by  the  physical  network  (or  was  sent  out  with  a  bad  FCS),
the  FCS  field  given  will  not  match  the  one  calculated  by  the  receiver.
FCS  errors  are  also  called  "CRC  errors"  or  "Checksum  errors"  (the
FCS code implemented is CRC32).

Fragments

Increments on reception of a frame shorter than 64 bytes with an FCS
(CRC) error or an alignment error (see Align Errors below).

Note

: It is entirely normal for fragments counter to increment for a port

in the half-

duplex mode because “runts” (interrupted frames due to

collisions) are counted.

Alignment Errors

Increments when a received Ethernet frame is not “octet-aligned” i.e.
its total number of bits is not a multiple of 8. Align(ment) errors are
also called "Framing Errors" by other vendors and books.

«
...
119
120
121
122
123
...
»

Summary of Contents for 86498 ETHER-1000 UNIT















































































































































































Reviews:

No comments

Related manuals for 86498 ETHER-1000 UNIT

Brand: Visara Pages: 12

Brand: Sony Pages: 36

Brand: Sony Pages: 40

Brand: SW Stahl PROFI Tools Pages: 72

Brand: Velleman Pages: 16

Brand: Sanwa Pages: 42

Brand: Sanwa Pages: 72

Brand: APPA Pages: 24

Brand: Miranda Pages: 19

Brand: CTC Union Pages: 26

Brand: UEi Pages: 9

Brand: YATO Pages: 64

Brand: Excalibur Pages: 228

NMEA Multiplexer

Brand: Raymarine Pages: 16

Brand: Keithley Pages: 18

Brand: Tempo Fitness Pages: 55

Brand: Testboy Pages: 70

Brand: SP tools Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands