GCC Technologies P3-132S User Manual Download

Page: 24 / 179

Puma III User Manual

Installation 2-13

2.6 Cable Connections

Puma III communicates with a computer through

USB (Universal Serial Bus),

or Serial port

(RS-232C)

. This chapter shows you how to connect the cutting

plotter to a host computer and how to set up the computer/cutting plotter

interconnection.

Notice:

When USB connection is enabled, serial port will be disabled

automatically.

2.6.1 USB Interface

Puma III build-in USB interface are based on the Universal Serial Bus

Specifications Revision 2.0 (Full Speed).

Serial Interface Connector (RS232C)

used to connect the cutting plotter to a

computer through a serial interface cable.

Figure 2-18

USB Connector

used to connect the cutting plotter to a

computer through a USB cable.

Summary of Contents for P3-132S




















































































































































































Search results

Summary of Contents for P3-132S

Reviews:

Related manuals for P3-132S

Brands by name

Popular brands

GCC Technologies P3-132S, User Manual

Search results

Summary of Contents for P3-132S

Reviews:

Related manuals for P3-132S

Brands by name

Popular brands