background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 14

Operating Instructions

Film Loading & Threading

The top and bottom rolls of laminating film must be
of the same width and be present simultaneously. A
small amount of adhesive will “squeeze out” during
lamination. Hardened adhesive deposits can
damage the heat rollers. To avoid any damage,
select “Low-Prs LAMI.” for job mode (    ), rotate the
rollers at slowest speed with heat on. Refer to the
section entitled CARING FOR THE FALCON 60
+ (-1) LAMINATOR 
for instructions regarding
removal of the accumulated adhesive.
Adhesive will deposit on the rollers if:
- Only one roll is used.
- Different widths of rolls are loaded together.
- Either roll is loaded adhesive side against a heat
roller.
- One or both rolls of film are allowed to run
completely off its core.
The adhesive side of the film is on the inner side of
the web (Figure 20). The shiny side of clear film
must contact the heat rollers. The dull side of the film
contains the adhesive. Use extreme caution when
loading delustered (matte) film as both sides appear
dull.
Always change the top and bottom supply rolls at
the same time. Near the end of each roll of GBC
laminating film is a label stating “Warning-End of
Roll”. The appearance of this label on either the top
or bottom roll requires that new rolls of film be
installed as soon as the item presently being
laminated completely exits the rear of the laminator.
Do not introduce any additional items into the
laminator when the warning label is visible.

To load a roll of film; (Figure 21)
1. Pull the clevis pin up.
2. Swing shaft outward.
3. Slide the roll of film onto the film shaft ensuring
adhesive side is out.
4. Push the film shaft back into the film shaft
support saddle.
5. Push the clevis pin down.
6. Center the roll of film.

Fig 20

Fig 21

Summary of Contents for Falcon 60+ (-1)




























Reviews: