background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 9

Fig 5

Fig 6

Fig 7

Features Guide

A. POWER ON/ OFF: (Figure 5) Located at the back
left of the machine applies power to the laminator.
The control panel display will illuminate when
position  marked “l” is pushed. The off  position,
marked “O”, removes power from the laminator.

B. CONTROL PANEL INDICATORS: (Figure 6)

1. POWER INDICATOR

Illuminates when the

laminator is plugged in and POWER ON/ OFF is in
the on, (I), position.

2. PRESSURE INDICATOR  : Illuminates in
increments to correspond with the amount of
pressure at the main roller nip. Pressure is
represented by percent from 0 (minimal) to 100
(maximum).

3. READY INDICATOR: “READY” Illuminates when
the actual temperature is equal to (+/- 5) set
temperature.

4. °C INDICATOR: “°C” Illuminates indicating the
displayed value is in degrees Celsius.

5. °F INDICATOR: “°F” Illuminates indicating the
displayed value is in degrees Fahrenheit.

6. ON INDICATORS    : Located near the heater
and cooling fan on buttons. Illuminates when the
related on button is pressed.

7. SELECTION INDICATORS    : Located near the
start/ stop and forward/ reverse buttons. Illuminates
when the selected button is pressed.

C. CONTROL PANEL BUTTONS: (Figure 7)

1. START   : When pressed, indicator illuminates
and activates rollers for normal operation.

2. STOP    : When pressed, indicator illuminates
and stops the movement of the rollers.

3. REVERSE    : When pressed, indicator
illuminates and sets the motor direction for reverse
roller movement to clear film jams and wrap-ups.

4. FORWARD   : When pressed, indicator
illuminates and sets the motor direction for forward
roller movement to run in normal operation mode.

For items 5 -13, refer to Figure 8.

Summary of Contents for Falcon 60+ (-1)




























Reviews: