background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 10

5. SPEED   : This means machine roller speed.
Turn clockwise to increase speed or
counterclockwise to decrease speed. Speed range
is 1 - 10.

6. TEMPERATURE CONTROLS: The upper and
lower heaters have identical controls, on, off,
increase, decrease and measure. The top set of
controls relate to the upper heater (   ) and the lower
set of controls relate to the lower heater (   ).

7. TEMPERATURE CONTROL ON  :

When

pressed, indicator illuminates and turns power on to
the temperature controller unit.

8. TEMPERATURE CONTROL OFF  : When
pressed, turns power off to the temperature
controller unit.

9. TEMPERATURE INCREASE     :

When

pressed, increases the temperature set point value.

10. TEMPERATURE DECREASE        :

When

pressed, decreases the temperature set point
value.

11. TEMPERATURE MEASURE: When pressed,
flashes the actual temperature of the roller.

12. COOLING    ON   : When pressed, indicator
illuminates and turns on the cooling fans.

13. COOLING     OFF   : When pressed, turns off 
the cooling fans.

D. E-STOP: Four emergency stop buttons exist on
the laminator. Two located on the left and right front
and two on the left and right rear of the laminator.
(Figure 9)

To engage, push (1) any emergency stop push
button. Power to the motor is removed. To disen-
gage, turn (2) the push button 1/4 turn
counterclockwise.

E. SAFETY SHIELD INTERLOCK LATCH: (Figure
10) Used to lock the safety shield into position and
activate an interlock switch. The interlock latch is
located on the left side of the safety shield. When
pushed to the full left (1), the safety shield is locked.
When pushed to the full right (2), the safety shield is
unlocked.

Fig 8

Fig 9

Fig 10

Summary of Contents for Falcon 60+ (-1)




























Reviews: