background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 13

W. REAR TABLE  LATCHES: (Figure 17) Located
under the left and right sides of the rear table.

X. REAR TABLE: (Figure 17) Provides a working
surface when operating the machine from the rear.
This table may also be lowered when webbing for
roll to roll applications.

To lower, pull the left and right side rear table latches
in and lower the rear table.

Y. REAR RUN/ STOP SWITCH:

(Figure 18)

Located on the right side of the laminator from the
rear operating position. This switch permits run (1) /
stop (2) control of the motor from the rear operating
position.

Z. FILM WEB:

Laminating film loaded into the

machine.

a. NIP POINT: The point at which the top and
bottom rollers come into contact. The Nip Point of
the heat rollers is the place at which the items for
lamination are introduced into the laminator.

b. REAR SLITTER: (Figure 19) Used to cut off the
laminated web. To use, push down on the blade
engage lever (1) and slide across the rear slitter rail
(2) to the opposite side.

c. SEPARATOR BAR:

(Option) (Figure 19)

Required if running Accushield™ material. To install,
remove the rear slitter and position the separator bar
in it’s place.

(Falcon 60+ (-1) Part # 2020577)

Fig 17

Fig 18

Fig 19

Summary of Contents for Falcon 60+ (-1)




























Reviews: