background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 16

Webbing PSA Film/Mount Adhesive

Using Threading  Card

The laminator should be cool to the touch before
proceeding.

1. Turn the Power ON/OFF to on (I).

2. Load the rolls of film as illustrated in Figure 25.
Ensure no brake tension is applied to the film shafts.

3. Remove the safety shield and pivot the feed table
down.

4. Pull the top roll of film down under the idler bar
and up to the upper front rewind tube.

5. Place one piece of masking tape in the center of
the film and secure to the rewind tube.

6. Make two full wraps around the rewind tube, then
carefully score the laminate without cutting the
release liner. Pull the laminate down allowing it to
drape over the upper heat roller (Figure 25).

7. Pull the mount adhesive up towards the film
draped over the upper heat roller (Figure 26).

8. Use a threading card to push the two materials
through the heat roller nip.

9. Pivot the table back to it’s feeding position while
ensuring the threading card is on top of the feed
table (Figure 27).

10. Replace the safety shield.

11. Use the main roller pressure handle to bring the
main roller to initial contact with the threading card.
Set speed to 3 or less.

12. Set speed to 3 or less. Ensure forward (   ) is
selected and press the start (    ) button.

13. From the rear of the machine, guide the web
over the chill idler, if installed, and through the pull
rollers.

14. Once the web has entered the pull roller nip, use
the pull roller pressure handle to close the pull roller
nip.

15. Press the stop (   ) button Once the threading
card has completely exited the pull rollers,.

16. Open the main roller nip.

17. Now refer to the section entitled START
LAMINATING.

Fig 25

Fig 26

Fig 27

Summary of Contents for Falcon 60+ (-1)




























Reviews: