background image

Falcon 60+ (-1)

Falcon 60+ (-1)

WARNING: THE SAFETY ALERT SYMBOL
PRECEDES EACH SAFETY MESSAGE IN
THIS INSTRUCTION MANUAL.

THE

SYMBOL INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD TO YOU OR OTHERS, AS
WELL AS PRODUCT OR PROPERTY DAMAGE.

WARNING:

DO NOT ATTEMPT TO

SERVICE OR REPAIR THE FALCON 60+ (-
1) LAMINATOR.

WARNING:

DO NOT CONNECT THE

LAMINATOR TO AN ELECTRICAL SUPPLY
OR ATTEMPT TO OPERATE THE

LAMINATOR UNTIL YOU HAVE COMPLETELY
READ THESE  INSTRUCTIONS.

MAINTAIN

THESE INSTRUCTIONS IN A CONVENIENT
LOCATION FOR FUTURE REFERENCE.

Operations Manual

© 2003 General Binding Corporation

Page 3

Important Safety Instructions

YOUR SAFETY AS WELL AS THE SAFETY OF
OTHERS IS IMPORTANT TO GBC.

IN THIS

INSTRUCTION MANUAL AND ON THE
PRODUCT, YOU WILL FIND IMPORTANT SAFETY
MESSAGES REGARDING THE PRODUCT. READ
THESE MESSAGES CAREFULLY. READ ALL OF
THE INSTRUCTIONS AND SAVE THESE
INSTRUCTIONS FOR LATER USE.

THE SAFETY ALERT SYMBOL PRECEDES
EACH SAFETY MESSAGE IN THIS
INSTRUCTION MANUAL.

THE SYMBOL

INDICATES A POTENTIAL PERSONAL SAFETY
HAZARD TO YOU OR OTHERS, AS WELL AS
PRODUCT OR PROPERTY DAMAGE.
THE FOLLOWING WARNINGS ARE FOUND
UPON THIS  PRODUCT.

THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE SERIOUSLY HURT OR KILLED IF
YOU OPEN THE PRODUCT AND EXPOSE
YOURSELF TO  HAZARDOUS VOLTAGE.

THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE BURNED AND YOUR FINGERS AND
HANDS COULD BE TRAPPED AND CRUSHED IN
THE HOT ROLLERS. CLOTHING, JEWELRY AND
LONG HAIR COULD BE CAUGHT IN THE
ROLLERS AND PULL YOU INTO THEM.

THIS SAFETY MESSAGE MEANS THAT YOU
COULD CUT YOURSELF IF YOU ARE NOT
CAREFUL.

Summary of Contents for Falcon 60+ (-1)




























Reviews: