background image

Falcon 60+ (-1)

Falcon 60+ (-1)

Operations Manual

© 2003 General Binding Corporation

Page 17

Start Laminating

1. At this point you should have your laminator
webbed with the appropriate material for your
application.

2. The safety shield and feed table should be in the
normal operating position.

3. The main rollers should be open and the pull
rollers should be closed.

4. Speed is set to 3 or less and forward () motor
direction is selected .

5. Press the start () button.

6. Set main roller pressure between 40 - 50% for
laminating.

CAUTION: If using PSA film, an air pocket
may result between the main rollers and pull
rollers. Raise the pull rollers to allow the air

pocket to pass.

7. Make any necessary film brake tension, pull/
main roller pressure, clutch and/ or rewind brake
tension adjustments. Refer to the section entitled
SPEED/ TEMPERATURE  GUIDE.

8. Position the item to be laminated on the feed
table.

9. Align the leading edge of the item square to the
heat roller nip (Figure 28).

10. With both hands and an outward force push the
image slower than the speed of the rollers into the
nip of the heat rollers (Figure 29).

CAUTION: Avoid forcing the image into the
main roller nip as this action will cause the
corners of the leading edge to buckle and

create a wave.

Fig 28

Fig 29

Summary of Contents for Falcon 60+ (-1)




























Reviews: