Gateway 930 series System Manual Download

Page: 51 / 160

Drives

Removing an empty drive carrier

If the system ships with less than six drives installed, the empty drive bays
contain drive carriers.

If you need to replace an empty drive carrier in the system, make sure it slides
straight into place until the plastic handle begins to move upward, then close
the handle.

To remove an empty drive carrier:

If the drive carrier is locked, use the hex key to unlock the carrier. Locked
drive carriers show a red flag in the slot on the carrier handle.

Remove the drive carrier from the drive bay by pressing down on the
carrier handle and rotating the handle out and down from the front of
the server.

8508088.book Page 43 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands