Gateway 930 series System Manual Download Page 144 | Manualshive

Page: 144 / 160

background image

136

Safety and Regulatory Information

The

Ringer Equivalence Number

(REN) assigned to each terminal device provides an indication

of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.

Laser safety statement

All Gateway systems equipped with CD and DVD drives comply with the appropriate safety
standards, including IEC 825. The laser devices in these components are classified as “Class 1
Laser Products” under a US Department of Health and Human Services (DHHS) Radiation
Performance Standard. Should the unit ever need servicing, contact an authorized service
location.

Warning

Use of controls or adjustments or performance of
procedures other than those specified in this manual may
result in hazardous radiation exposure. To prevent
exposure to laser beams, do not try to open the enclosure
of a CD or DVD drive.

8508088.book Page 136 Thursday, November 1, 2001 9:35 AM

«
...
142
143
144
145
146
...
»

Summary of Contents for 930 series

































































































































































Reviews:

No comments

Related manuals for 930 series

ALTOS R910 Series

Brand: Acer Pages: 74

SuperServer 5013C-MT

Brand: Supero Pages: 98

Brand: Aaeon Pages: 38

Transport GT26-B4987

Brand: TYAN Pages: 125

Brand: 360 Systems Pages: 148

R120d-1E N8100-1954F

Brand: NEC Pages: 166

Brand: Motorola Pages: 40

Brand: Motorola Pages: 90

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 316

Brand: Panasonic Pages: 456

TS-269L TurboNAS

Brand: QNAP Pages: 6

60 Business Phone

Brand: ESI Pages: 2

SDSTX3110-121S-LRT

Brand: Transition Networks Pages: 109

cPCI-6510 Series

Brand: ADLINK Technology Pages: 112

MultiAccess MULTIACCESS MA30120

Brand: Multitech Pages: 179

Brand: 3onedata Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands