Gateway 930 series System Manual Download

Page: 10 / 160

System Features

Front panel

Chassis lock

prevents unauthorized access to both the front panel controls

and to the interior of the system by locking the front bezel to the chassis.

Power LED

glows green whenever the system is turned on. The LED also

flashes when the system is in sleep mode.

Disk activity LED

glows green whenever a drive is actively reading or writing

data.

System fault LED

(steady yellow) indicates an uncorrectable ECC (Error

Checking and Correcting) system memory fault, a fan temperature or voltage
problem, or a chassis intrusion alert.

5.25” drive bay

CD drive

Diskette drive

Reserved

Hot-plug
drive bay

Front panel door
(shown open)

Chassis lock

Power LED

Disk activity LED

System fault LED

System reset

button

Power button

Hot-plug drive
activity LED

Hot-plug drive lock

Outriggers

Castors

PS 2 status LED

PS 1 status LED

System fault LED
reset switch

8508088.book Page 2 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands