Gateway 930 series System Manual Download Page 73 | Manualshive

Page: 73 / 160

background image

Expansion cards

65

8

Press the card guide release tab upward to release the cards and allow the
new card to be inserted into the card guide (for full-length expansion
cards).

9

Insert the bottom edge of the expansion card (the keyed edge with the
contacts) into the slot on the system board and push in firmly to seat
the card.

10

Once the card is securely placed, slide the card guide release tab down
again (for full-length expansion cards) and press the expansion card
retention clip through the back panel until it clicks into place to secure
the card.

11

Connect any cables to the card (see card documentation for proper cable
orientation).

Important

The card guide release tab is held in place during shipping
by a cotter pin. Remove the cotter pin before moving the
release tab. You can replace the cotter pin or leave it out.

Expansion card
retention clip

Card guide

release tab

8508088.book Page 65 Thursday, November 1, 2001 9:35 AM

«
...
71
72
73
74
75
...
»

Summary of Contents for 930 series

































































































































































Reviews:

No comments

Related manuals for 930 series

Network Space MAX

Brand: LaCie Pages: 2

8BIG RACK THUNDERBOLT 2

Brand: LaCie Pages: 28

Brand: ioCorp Pages: 18

Brand: Jung Pages: 16

FusionServer G5500 V6

Brand: xFusion Digital Technologies Pages: 100

Brand: Synology Pages: 24

Brand: QUANTA Pages: 177

Brand: Gigabyte Pages: 120

Disk On-line Server NAS-2100

Brand: QNAP Pages: 112

SuperStorageSystem SSG-2028R-DN2R40L

Brand: Supermicro Pages: 84

Brand: Supero Pages: 130

WF01 64 V2 Series

Brand: Lanberg Pages: 22

Brand: AirLive Pages: 89

Brand: ICP DAS USA Pages: 8

Brand: Ambient Weather Pages: 24

SPARC Enterprise M3000

Brand: Oracle Pages: 552

Brand: Oracle Pages: 34

Brand: Gigabyte Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands