GAS BreathSpec User Manual Download Page 42

Page: 42 / 242

BreathSpec®

– User Manual

42/242

5.5.2 Front

Figure 11: BreathSpec® (Version 4G2) with Airsense µTD - Housing of device - Front

Power LED

•

Indicates whether or not the

device is connected to a power
supply and is switched on

•

Indicates an internal system

error.

USB Socket

USB socket for connecting external USB
storage volumes. These volumes can be
used for:

•

exporting measurement files

•

importing sample name lists

•

upgrading the device’s firmware

•

saving/loading system settings.

Sample in socket

3 mm Swagelok inlet plug for connecting
the device to a gas source via

•

Bypass Adapter

•

Transfer-line or

•

Luer-Lock-Adapter.

Summary of Contents for BreathSpec



















































































































































































































































Search results

Summary of Contents for BreathSpec

Reviews:

Related manuals for BreathSpec

Brands by name

Popular brands

GAS BreathSpec, User Manual

Search results

Summary of Contents for BreathSpec

Reviews:

Related manuals for BreathSpec

Brands by name

Popular brands