manualshive.com logo in svg

GAS BreathSpec, User Manual

Share
Download
GAS BreathSpec User Manual Download Page 54

BreathSpec® 

– User Manual 

 

54/242 
 

 

Recording Check Box 

The live monitoring of measurements can 
be recorded manually. The available 
storage capacity in minutes is displayed. 

 

Drift Voltage Mode 

Displays the current selected Drift 
Voltage state (positive / negative). 

 

Device Parameter 

Displays the current temperature, flow 
and pressure values. 

 

6.2.2  Measurement modes 

 
Two measurement modes are available: 

• 

Measurement with user defined programs 

• 

Manually operated measurement 

 

6.2.2.1  Measurement with user defined programs  

 
In this mode data acquisition with user-defined measurement programs can be started. 

The executable measurement program can be created and selected in the Programs 

Window. The name of the current selected program is displayed in the upper left of the 

Spectra Window. The selected measurement program can be started by activating the 

Program button in the upper left of the Spectra Window.  

 

Figure 21: Start Program 

 
 

 

Summary of Contents for BreathSpec



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands