background image

Part # 4521653 Rev 1 (03/05/13)

Page 7

INDIVIDUAL MODEL INSTALLATIONS

Hot Plate – Model ED-15H

Wall Clearances

Do not install appliance closer to a wall of combustible 

material than:

 

Back 1 ½” (38mm)

 

Sides 1 ½” (38mm)

Supply Connection

For supply connection, use wire suitable for 90°C (194°F).

Electrical Connection

A knockout is provided near the front left side of the unit 

located behind the control panel. To view knockout, loosen 

the two acorn nuts and hinge control panel downward. The 

terminal block is also located in this area.

The supply cable entrance is located on the right side when 

facing the rear of the unit. The cable is fed towards the front 

through a wire way.

Controls

Infinite switches are used to control the tubular elements:

 

HI to 5  - 

High Heat

 

5 to 3 

Medium Heat

 

3 to LO  - 

Low Heat

Setting of switches between the numbers will give 

intermediate heat. Switches are reversible and may be 

turned right or left.

Solid Elements Hot Plate –  

Model ED-15HSE / ED-15THSE

Wall Clearances

Do not install appliance closer to a wall of combustible 

material than:

 

Back 1 ½” (38mm)

 

Sides 1 ½” (38mm)

Supply Connection

For supply connection, use wire suitable for 75°C (167°F).

NOTE: - All 208V 1 phase 60 hZ ED-15THSE models are 

equipped with a 4-ft (1219mm) power cord and  

NEMA L6-30P plug (HUBBELL HBL2621 or equivalent).

Electrical Connection

A knockout is provided near the front left side of the unit 

located behind the control panel. To view knockout, loosen 

the two acorn nuts and hinge control panel downward. The 

terminal block is also located in this area.

The supply cable entrance is located on the right side when 

facing the rear of the unit. The cable is fed towards the front 

through a wire way.

Controls

Solid element hot plates are controlled by a six heat switch. 

There are three boiling and three simmering positions. Turn 

the switch left or right from the off position to the desired 

number, one being the lowest setting and six being the 

highest.

SWITCH 

POSITION

WATTAGE

HEAT

15HSE

15THSE

1

240

200

Low (Simmer)

2

340

305

3

450

450

Medium

4

1300

950

5

1750

1400

High (Boil)

6

2600

2000

This hot plate is protected against overheating when running 

empty or when using poor quality cookware, by a unique 

built-in bimetal protector switch.

This protector cuts down the power automatically under the 

above conditions, overriding the regular switch and it resets 

itself when conditions return to normal. This is an important 

safety feature.

Before Operating The Hot Plate

The top working surface has a heat resistant coating. Before 

using the sealed hot plates for the first time, they should 

be heated for a short period without a pan to harden and 

burn off the protective coating (3-5 minutes at the highest 

setting).

Sealed Hot Plates

All purpose sealed top elements provide an ease-clean top. 

They are intended for boiling, simmering, sauté and other 

top cooking.

Summary of Contents for ED Series

































Reviews: