20
4.1.2. Non-Emergency Speech Call
This function is only available when Command
#7 is programmed.
Step 1.
From Idle mode, press and hold
the
RESET
button for 3 seconds until
CTC-1052RV emits a short beep.
Step 2.
Release the button and
one short
beep
will sound. CTC-1052RV dials
the phone number entered in
Command #7.
<
<
N
N
O
O
T
T
E
E
>
>
)
When 5 short beeps (warning beeps)
sound instead of a short beep, it means
CTC-1052RV is not in idle mode and it is
not allowed to use non-emergency call
function.
Step 3.
If the dialing succeeds, CTC-1052RV
will open a two-way voice
communication between the call
recipient and CTC-1052RV for 30
minutes. The Red button backlight will
illuminate during the communication.
<
<
N
N
O
O
T
T
E
E
>
>
)
If the dialing fails, CTC-1052RV will not
retry.
)
Press Reset button can stop and cancel
the dialing & call at any time.
Step 4.
At the last 20 & 10 secs, CTC-1052RV
will emit a beep via the telephone
handset to alert the call recipient. If
the Call Recipient needs more
conversation time, press any DTMF
key can add another 30 minutes.
<
<
N
N
O
O
T
T
E
E
>
>
)
30-minute
is allowed for each call and is
inextensible.
Step 5.
Press DTMF 9 or Reset button, or
hang up to terminate the call. The Red
button backlight dims and CTC-
1052RV returns to idle mode.
4.1.3. AC Power Check Up
z
If the AC Power failure is detected for 10
seconds or longer, the GREEN LED starts
to flash as a visual warning to the user.
GSM will be then be powered down. Thus,
Remote Programming is unavailable.
GSM will be powered up only at times of
reporting
z
Once the AC Power resumes, the GREEN
LED turns steady on again.
z
If the AC Power failure lasts for an hour,
CTC-1052RV will send an AC Failure
report to the Monitoring Center.
z
After the Power restoration lasts more
than one hour, CTC-1052RV will report AC
Restore to the Monitoring Center.
z
During the AC Power failure period, Call-
Back function is automatically disabled.
4.1.4. CTC-1052RV Low Battery
z
CTC-1052RV continuously checks its own
Battery Condition 30 minutes after
powering up.
z
When the battery low condition lasts for
4 -
6 mins
, CTC-1052RV will report to the
Monitoring Center and the GREEN LED
flashes slowly.
z
Press
the
RESET
button to clear the
warning beeps, and the LED returns to
steady ON.
4.1.5. Devices Low Battery
z
When CTC-1052RV receives a battery low
signal from a particular device, it will report
to the Monitoring Center and the GREEN
LED will flash rapidly until the fault
condition is cleared.
4.1.6. Automatic Check-in Report =
Periodic Test Call
z
When CTC-1052RV is programmed to
send a periodical check-in report, CTC-
1052RV will report to the Monitoring
Center accordingly.
z
The Periodic-Check-in Timer will be reset
whenever Programming Mode is entered.
4.1.7. Mobility Timer
z
In order to check the user’s well being, a
Mobility Timer can be set by using
Command #44.
z
If Mobility Timer is set as
Enable
, a
counting down period starts from:
Summary of Contents for CTC-1052RV
Page 1: ...E1 MAR 30 2011...
