GARDASOFT TR-HT2 Series User Manual Download Page 43 | Manualshive

Page: 43 / 78

background image

TR-HT2xx LED Controller - User Manual

10

Ethernet address

You may need to ask your network administrator for advice about setting
up the Ethernet connection.

The application note APP923 – Troubleshooting Ethernet problems is
available from

www.gardasoft.com/Downloads

The Ethernet set up of the TR-HT is not affected by cold-booting the
controller.

10.1

IP address

The TR-HT needs an Internet Protocol (IP) address to communicate over
Ethernet. There are two ways to get an IP address; either programmed
into the unit or using DHCP.

For DHCP mode, the TR-HT acquires its IP address, subnet mask, and
gateway address from the DHCP server. Otherwise the TR-HT has a fixed
IP address, subnet mask, and gateway address.

DHCP mode or the IP address can be set or read using the
GardasoftMaint program available from

www.gardasoft.com/Downloads

.

The GardasoftMaint window is shown below:

—

43

—

«
...
41
42
43
44
45
...
»

Summary of Contents for TR-HT2 Series















































































Reviews:

No comments

Related manuals for TR-HT2 Series

Brand: Aalborg Pages: 128

ACTIVE DRIVER M/M 1.1

Brand: DAB Pages: 10

Brand: d&b audiotechnik Pages: 3

ACTIVE DRIVER M/M 1.1

Brand: DAB PUMPS Pages: 38

Brand: Dakota Digital Pages: 6

CMD-2000 Series

Brand: Dakota Digital Pages: 10

Brand: Z-Wave Pages: 6

Brand: Salda Pages: 20

Brand: Lamtec Pages: 136

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

Brand: BQT Pages: 2

Brand: DAY Pages: 23

Lift Inverter L1000V

Brand: YASKAWA Pages: 282

Brand: Samwon Tech Pages: 104

Brand: ADEMCO Pages: 4

Brand: Baby Trend Pages: 20

Brand: Guangdong Schen Investment Pages: 15

Brand: Niko Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands