GARDASOFT TR-HT2 Series User Manual Download Page 56

Page: 56 / 78

TR-HT2xx LED Controller - User Manual

Use the

and

buttons to select

Int Trig

and press the

SEL

button.

The inernal trigger timer is set to

Off

. Press

the

SEL

button to end the sequence.

Or...

Use the

and

buttons to select

to set

up the internal trigger. Press the

SEL

button.

Set range

is displayed. Use the

and

buttons to change the range

press the

SEL

button to enter a time value. For

information about setting a time value, refer
to

Section 12.2.7, Setting time periods

The internal trigger timer is set.

12.2.9 Using the key lock

You can lock the TR-HT front panel keypad so unauthorised users cannot
change the configuration. To do this you can set a numeric code from 0 to
255, which provides moderate protection.

To lock the keypad, press and hold

SEL

for 1 second,

Select Opt

and

Chan 1

are displayed. Follow the keystrokes below:

Use the

and

buttons to scroll to

Key-

lock

and press the

SEL

button.

Unlock is displayed. Use the

and

buttons to select

Lock

and press the

SEL

button.

0 is displayed. Use the

and

buttons to

set a lock code value from 0 to 255, and press
the

SEL

button.

The TR-HT keypad is locked.

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands