GARDASOFT TR-HT2 Series User Manual Download Page 54

Page: 54 / 78

TR-HT2xx LED Controller - User Manual

Delay

is displayed with a setting of XXX us

highlighted. Press the

SEL

button to set up a

pulse delay time

use the

and

buttons

to change the range. For information about
setting a time value, refer to

Section 12.2.7,

Setting time periods

Pulse

is displayed with a setting of X.XX ms

highlighted. Press the

SEL

button to set up a

pulse delay time

use the

and

buttons

to change the range. For information about
setting a time value, refer to

Section 12.2.7,

Setting time periods

Retrigger

is displayed with a setting of X.XX

ms highlighted. Press the

SEL

button to set

up a pulse delay time

use the

and

buttons to change the range. For information
about setting a time value, refer to

Section

12.2.7, Setting time periods

Trig 1

is displayed. Use the

and

buttons

to select

Trig 2

if you want to use trigger input

2. Press the

SEL

button.

The trigger is set to

Positive

, or active high.

Press the

SEL

button to keep the trigger

positive.

Or...

If you wish to set the trigger negative, or
active low, use the

and

buttons to select

Negative

. Press the

SEL

button.

Error detection is disabled. Press the

SEL

button to keep it disabled.

Or...

If you wish to enable error detection, use the

and

buttons to set the

Err flag

Enabled

. Press the

SEL

button.

Pulsed operation is set up.

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands