GARDASOFT TR-HT2 Series User Manual Download Page 50

Page: 50 / 78

TR-HT2xx LED Controller - User Manual

12.2.2 Setting the light rating

Press and hold

SEL

for 1 second,

Select Opt

and

Chan 1

are displayed.

Use the

buttons to scroll to

Rating

, and follow the keystrokes

below:

Rating

is highlighted. Press the

SEL

button.

Chan 1

is highlighted. Use the

and

buttons to select the channel you want to set
the rating for, and press the

SEL

button.

Cur

is highlighted. Press the

SEL

button if

your light is current rated.

Or...

If your light is voltage rated, use the

and

buttons to select

Vol

, and press the

SEL

button.

For current rated lights, use the

and

buttons to set the rating in Amps, and press
the

SEL

button.

Or...

For voltage rated lights, use the

and

buttons to set the rating in volts, and press
the

SEL

button.

The light's rating is set up and the TR-HT is
ready to use.

12.2.3 Setting up continuous output

Press and hold

SEL

for 1 second,

Select Opt

and

Chan 1

are displayed.

Use the

buttons to select the channel you want to set up, and

follow the keystrokes below:

The channel you want to set up is highlighted.
Press the

SEL

button.

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands